Does Hail Damage Need To Be Repaired
The thing about hail damage is that a lot of the time it doesnt actually need to be repaired. In some extreme cases, hail damage will crack the paint on a car, it may also dent a panel so much that the integrity is questionable. In this scenario, a repair will be necessary.If the paint is still perfect and the dings are minor, Hail Damage is just ugly to look at. It wont cause any rust issues and will not need urgently repaired.That being said, if your car is your pride & joy, its completely understandable that you would get the hail damage repaired as soon as possible.
Remove Dent With A Hairdryer
With this method, you are using the power of temperature change from drastic hot and cold which helps the metal of the dent expand and contract which can be a great solution to remove small and annoying dents. You are going to need a few things with this, you will need aluminum foil, rubber-coated gloves, dry ice , a can of compressed air and lastly a hairdryer.
Use Hot Glue Wooden Dowels & Screws
When you attempt to take out dents yourself, you always put the risk that you might further damage your car, whether you make the dent worse or chip the paint. A safe way of trying to take out big dents on your car is by using several wooden dowels, a few screws, and a hot glue gun.
Simply place two nails into each side of the dowel and put the hot glue on the bottom. Place the dowels glue-side down in areas around the dent, repeat as many times as needed to cover the area, let them dry, and pull each one out until the dent is gone.
Place and pull the same dowels in several different places across the dent until most of it comes out. If you’re going to try this method, make sure that you have enough glue and some patience. Use rubbing alcohol or heat to detach the glue from the car.
Read Also: Does Carvana Lease
Hot Glue Wooden Dowels And Screws Pulling Method
This method takes some engineering on your part but it is a good way to ensure that you dont chip the paint of your vehicle. You will use your own pulling force to release the dent over several areas where the dent has formed. Simply, place screws on the end of small wooden dowels. This will act as a handle for you to pull on. You will use the hot glue to affix the dowels to the dent. Apply the dowels in evenly spaced areas over the dent. When the glue has dried, begin pulling on the dowels to pop the dent out of your vehicle. You will be able to get maximum force over the dent and pull it out over several areas of impact. This will leave your car or truck cover without any paint chips as it is a safe way to pull out a dent.
Touching Up Your Cars Paint

After youve fixed the dent, you may need to touch up your cars paint. Heres how to do that.
A bumped bumper!
Also Check: National Highway Traffic Safety Administration’s Vin Decoder
Get Help To Repair Car Dents From A Mechanic On Justanswer
The Drive recognizes that while our How-To guides are detailed and easily followed, a rusty bolt, an engine component not in the correct position, or oil leaking everywhere can derail a project. Thats why weve partnered with JustAnswer, which connects you to certified mechanics around the globe, to get you through even the toughest jobs.
So if you have a question or are stuck, and talk to a mechanic near you.
Read Also: How Much Mileage Is Too Much For A Used Car
How To Remove Dents With A Plunger
This is the sort of thing you should be looking for.
Recommended Reading: What Does It Cost To Have A Car Painted
Bust Out The Vacuum Cleaner
Up next in strange tools you can use to repair car dents is your standard household vacuum cleaner. The only other tool youll need for this very simple fix is a bucket. To start, poke a hole in the bottom of the bucket, and then place the top of the bucket firmly over the dented area. Place the vacuum hose over the hole in the bucket and turn it on. From there its simply a matter of waiting until the dent pops out. Keep in mind that this fix is best used for dents of the smaller variety.
The Old Classic: Use Boiling Water
This dependable method works wonders for those who have simply reversed into an object. Before we begin, this trick should only be attempted if your bumper is composed of plastic. Plastic is a synthetic and flexible material which when soft, can easily be molded into shape. This molding is what the boiling water achieves. The moment youve poured the water over the dent, reach quickly behind your bumper and try to pop the dent back in. The trick to this method is to work as quickly as possible the heat produced by the boiling water wont last forever!
Most people attempt this simply by boiling a kettle and pouring it over the bump. However, several DIYers state that its more effective to fill up a saucepan and hold the water against the bump for a substantial period of time.
Another debatable hack with the boiling water method is to pour cold water on the plastic after its original shape has been attained, in order to help further set it.
Dont start thinking youre the indestructible Hound from Game of Thrones or anything while attempting this procedure. Always wear a pair of gloves when reaching into the bonnet. There is a multitude of unknown objects lying around in there which have the potential to badly hurt your hand.
You May Like: How Much Does It Cost To Charge Car Ac
The Boiling Water Method
This method works for dents on plastic bumpers or the parts of your vehicle that are made of plastic.
- Boil a pot of water and pour it over the dented part of your bumper.
- Reach the back of the bumper and clear the dent.
- You can also remove the bumper if you cant reach the bump.
- Finally, pour a pot of cold water over the bumper to cool and secure the plastic area.
How To Apply The Final Coat
For the final coat, you can take it to your local body repair shop for a professional paint or do it yourself. Youâre going to have to get exactly your color in a spray can. If you have a spray gun run by a compressor, even better.
- Once again mask everything off and apply three or four even coats over the area over the period of a day. Let it dry hard overnight.
- Wrap the 800 grit wet sandpaper around the sanding block and slowly start sanding smooth. Take it right into the edge of the good coat on your car to make sure the new paint blends in. Always keep the area wet while sanding.
- Then once youâre okay with it being smooth itâs going to look very dull. Take to the area with a rag and the cutting polish compound. Once again keep the area wet and rub it for about ten minutes.
- Lastly take a fresh dry rag and polish it normally with car polish. If it still looks dull then go back to polishing it with the cutting compound and try the final polish until it shines like the rest of the good paint.
This article is accurate and true to the best of the authors knowledge. Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.
Also Check: How Much Does Registration Cost In California
How Do I Fix A Small Dent In My Car
Cars are not indestructible. Unless you are driving a tank, any vehicle can suffer from small dings and dents. These small dents may seem harmless, but there can be long-lasing consequences. Small dents may have internal damage along with being an eyesore for your car. Even worse, these dents may be from no fault of your own. In some cases, car owners park their car and return hours later to see a dent that was not there before. Luckily, there are a few methods that can repair small auto body dents.
What do I need to fix a small dent in my car?
Remember, auto insurance companies may recommend filing a claim for any kind of auto body repair, even the smallest dents. Car owners have options before calling their insurance representative. There are at-home ways to fix small dents in cars. These methods vary depending on the size, depth and location of the dent. Do-it-yourself methods can fix small dents with the help of these items:
None of these DIY methods for small dent repair is a guarantee. These methods can work, but they all come with different results. Dent repair with these methods are trial and error processes.
How do I prevent small dents to my car?
- Always checking and adjusting mirrors before putting the car in drive or reverse
- Being aware of surroundings when entering, exiting or driving around busy areas
- Parking away from other cars or toward the back of a parking lot
Free Estimate and Get Your Car Fixed
Simple Ways To Remove Smaller Dents From Your Car

Theres nothing more annoying than getting a dent on your newly purchased car. Even if youre a careful driver, you cant always avoid falling pine cones, wrongly parked cars or pebbles that hit your car when youre on the road. Since getting a dent removed by a professional can be unbelievably expensive, many of us would never consider fixing them.
However, dents, especially small ones, are not worth losing sleep over. There are plenty of ways to remove them from your car by using common household items such as a plunger, vacuum cleaner or aluminum foil. Not all of the methods will work for you, so you should decide which one would be the best for your car.
NOTE: If adentis too large, deep or has resulted in damaged metal, there is, unfortunately, no other way than bringing your car in for a repair.
Also Check: Who Accepts Carcareone Card
Solution : Boiling Water
Its not easy to push out dents on a plastic car bumper because plastics can be very stiff. However, a simple workaround would be to apply boiling water to the dent. Here are the steps to follow:
- Step 1: Pour boiling water on the dent
- Step 2: Reach out to the back of the bumper and push the dent out
The heat from the boiling water applied will make the plastic bumper more flexible and easier to put back in place.
Are There Common Dent Locations
Although dents can occur anywhere on your bodywork, some areas are more prone to prangs than others.
If you want to check your car for any irregularities, pay close attention to:
- doors Its easy to swing doors open into closely parked cars or other obstructions when youre not paying attention. Make sure you check all the way to the bottom of the door where high kerbs might have left a mark.
- bumpers Designed to minimise the impact of collisions, bumpers are one of the first places affected by motoring mishaps. Take a look at the front and back of your car for any dents that might need work.
Don’t Miss: 1 888 601 6302
Fix A Dent With Boiling Water
Like all of the techniques listed, this method requires equipment you can easily find at home. Fill the kettle and a bowl of water, find out a pair of rubber gloves to protect your hands and you are ready to test it out.
Step one: boil the kettle or pan and tip on the dent.Step two: while the area is still warm reach from the inside and pop out the dent.Step three: While popped back to its original shape pour the bowl of cold water onto the area to increase the cool down.
Ways To Remove Small Dents From Home
If you are the hands-on kind of person who likes to DIY then here are 5 ways you can take out a dent on the cheap. As a friendly disclaimer that we advise utmost caution and this advice should be used for entertainment purposes and not a hard and fast rule to fix dents. Just be aware that if you are not careful you make your dent problem worse.
Don’t Miss: Car Making Squealing Noise When Driving Stops When Braking
Pop Out The Dent With A Hair Dryer And Compressed Air
The combination of heat and pressure you can get from a hair dryer and compressed air may cause dents to pop out.
Start by heating the car dent with the hair dryer set at the highest temperature. This will expand the dent and make it more pliable.
When the car is hot to the touch, immediately spray the dented area with a can of compressed air. The cold air coming from the can will cause the area to contract. This should make the dent pop out.
Vacuum Cleaner And Bucket
The final method also uses common household tools, making it another easy approach to employ. In this case, you first need to cut a small hole in the bottom of a bucket . Next, cover the dent with the top of the bucket and put the vacuum cleaner hose over the hole at the bottom of the bucket. Lastly, turn on the vacuum and wait for the dent to disappear like magic.
Don’t Miss: Average Commission On Car Sales
You Can Use A Plunger
Another common way to fix a car dent is to do so with a plunger. You might already have one lying around your home, but weâre guessing youâd want to invest in a new one for this. Of course, this is best for particularly small dents since plungers are not that big.
With this method, you just attach the plunger to the dent and pour some water over both before pushing it down and then bringing it back up in the way youâd typically do so with a plunger. Repeat this a few times until the dent pops out. The good thing is this is likely to be far less messy than plunging a toilet.