How To Get Small Dents Out Of Car

With A Hair Dryer And An Air Duster

This one is actually the most popular one and tends to work for most. One can find these two things in pretty much every household. So, you actually dont need to spend anything at all. If you dont have it, were sure that your next door neighbor does.

Simply blow some hot air with the hair dryer right over the dent so as to heat it up. This will result in the expansion of the metal. Then take the air duster, hold it upside down, and start spraying on the dented area. The cold air followed by the hot will cause contraction and the dent will pop out.

How To Get A Dent Out Of Your Car With A Hammer

The method is pretty straightforward. Heres what you need to do.

• You need to have access to the rear side of the panel with the dent.
• Use the basic tools to get to the other side of the dent.
• Wrap the head of the hammer in a towel to minimize the impact.
• Tap the dent lightly with the hammer.;
• Keep tapping until the dent pops itself out.

Got A Scratch Return To Your Bathroom Yet Again

This time, grab the toothpaste!

You can easily remove superficial scratches that havent gone past the clear coat of paint on your car by gently buffing them out with toothpaste and a damp microfiber cloth. First, clean the area with a car washing soap and water and let it dry. Next, put a dab of toothpaste on the spot with the scratches and gently rub with your damp cloth. The toothpaste should remove the scratches, and once you notice them disappearing, you can stop.

Note that this trick only works on superficial scratches. To find out whether the scratches on your car are superficial, run your fingernail across them. If you feel your fingernail catch on the scratches, then they are deeper than the clear coat, and the fix might not work.

Also Check: How To Check Water In Car

Ready To Get Rid Of That Dented Car

If you have a car that has lots of issues and dents, you can sell that car quickly and easily! Cash Cars Buyer purchases cars with dents and we will buy your car FAST!;

Feeling hopeless about the dented car you have and you cant seem to find a fix? to get an offer on that car and let Cash Cars Buyer turn that dented car into dynamic cash, FAST!;

How To Repair A Dent With A Repair Kit

Buying tools specially made for the job might be the most effective approach of them all.;

There are three main types of dent repair kits:

• Pulling These kits use the same principle as the wooden dowel technique and work by gluing tabs to the dent and pulling.
• Tapping Some kits use metal pens designed to tap the dent out of your bodywork. They usually come with a range of heads to fix all kinds of damage.
• Pushing Alternatively, you could pick up tools designed to push dents outwards from the back of a panel. The kits usually supply different-sized rods but they dont come cheap.;

Its important to read the instructions provided and if you dont feel confident about taking on the job you can always contact an RAC approved garage for help.

Recommended Reading: How To Add Bluetooth To Car

Dented Your Car Dont Panic & Try One Of These 8 Things Instead

One of the most aggravating things for car enthusiasts is finding a dent in their precious vehicle. While one person might consider a tiny dent no big deal, for someone else, that same dent is enough to shatter their heart.

While car dents are merely aesthetic and dont cause physical harm to your vehicle, they can be embarrassing for some car owners. Nobody wants other people to look at their car and notice the deep depression on their cars body. Even worse, every time a car owner looks at their own vehicle, seeing that dent reminds them of the very thing that happened the day they received it.

If youre tired of that pesky dent lingering on your vehicle, no need to worry. Regardless of how big, small, major, or minor your dent is; how many your vehicle currently has; or how the dent were acquired, there are affordable and fairly quick ways to repair them.

Try one of the following methods to get rid of your cars dent today and next time, avoid dangerous areas, especially narrow streets with heavy traffic when parking your vehicle.

• Try the plunger method

Plungers arent just for removing blockages from pipes and drains. Your good ole plunger can also be used to eliminate a small- to medium-sized dimple on the surface of your vehicle. However, for this dent removal method to work, refrain from using a regular toilet or flange plumber. Instead, utilize a flat/cup plunger, which is normally used to unclog sinks.

• Hammer it back in place

• Use boiling water

• Try hot glue

How To Apply The Final Coat

For the final coat, you can take it to your local body repair shop for a professional paint or do it yourself. You’re going to have to get exactly your color in a spray can. If you have a spray gun run by a compressor, even better.

• Once again mask everything off and apply three or four even coats over the area over the period of a day. Let it dry hard overnight.
• Wrap the 800 grit wet sandpaper around the sanding block and slowly start sanding smooth. Take it right into the edge of the good coat on your car to make sure the new paint blends in. Always keep the area wet while sanding.
• Then once you’re okay with it being smooth it’s going to look very dull. Take to the area with a rag and the cutting polish compound. Once again keep the area wet and rub it for about ten minutes.
• Lastly take a fresh dry rag and polish it normally with car polish. If it still looks dull then go back to polishing it with the cutting compound and try the final polish until it shines like the rest of the good paint.

This article is accurate and true to the best of the authors knowledge. Content is for informational or entertainment purposes only and does not substitute for personal counsel or professional advice in business, financial, legal, or technical matters.

Also Check: Does Walmart Copy Car Keys

Can I Repair A Dent Myself

Yes, but youll need to make sure that the damage isnt too extensive first.;

Measure the dent and check that its no bigger than three inches in diameter and that its shallow, too. If the mark appears on a curve or a contour in the bodywork, a DIY approach probably isnt the best idea. Youll also need to be confident about working on your car and accessing the back of panels.;

Now its time to choose your method. Our step-by-step guides below highlight some of the best ways to get the job done.

If you find the idea of a DIY fix too complicated, a body shop or RAC approved garage will be able to help.

Remember, damage to the paintwork will have to be repaired separately.

How To Remove Or Repair Dents From Hail Damage

Getting dents on your car can be discouraging, but especially hail dents. Lots of little dents from hail damage can cause an unpleasant dimpled appearance on the surface of your hood, roof, and trunk. Fortunately, hail dents can be easily popped back out again or repaired by a;car;dent repair specialist.Here are a few tips for removing hail damage from your car.

DIY Dent Repair

For the DIYer, there are a few approaches you can use to try to remove the hail damage yourself. Sometimes a rapid change from hot to cold can cause the metal to pop back into shape again, removing the dent. Most of the DIY suggestions for removing hail dents use this approach.The first step of the DIY hail dent removal process is to heat the metal where the dent is.

Next, apply something cold to the area. The quick change in temperature should cause the dent to pop out within a few minutes.

• Lay a cold, wet cloth over the dent.Get a washcloth wet in cold water and lay it over the dent for several minutes.
• Spray compressed air over the dent.You know how cold those cans of air for cleaning your keyboard get while youre using them? That quick blast of cold air on your dent may be just what it needs to pop out cleanly.
• Apply dry ice to the dent.While wearing gloves to protect your hands, of course, put dry ice on the dent for several minutes, and it should pop out on its own.

When to Use a Professional Car;Dent Repair Service

You May Like: How To Change The Interior Of Your Car

Whats A Ding And Whats A Dent

Typically, a ding is defined as an unstructured blemish on a vehicle, that pushes the body inward. Usually, a ding is approximately 1/2 inch in diameter- and doesnt cause any damage to the paint of the car. It also never leaves an exposed area that can later rust. Shopping cars that run wild in a parking lot are a major culprit. Whether it be wind or a shopper that just rolls the cart from his or her vehicle- that cart can make its way to your vehicle, causing a small smashed in area on the body of your car. Carelessly opened car doors are also another major cause of dings.;

A dent is generally defined as a more extensively damaged areas on cars, that are crushed in to the body of the car- and they care suspectable to rust if left untreated. Generally, a dent requires some work from an auto professional. The only difference between a dent and ding, is the size of the area. And depending on the size of the dent, you could be looking at hundreds of dollars in repair.;

Get Help To Repair Car Dents From A Mechanic On Justanswer

The Drive recognizes that while our How-To guides are detailed and easily followed, a rusty bolt, an engine component not in the correct position, or oil leaking everywhere can derail a project. Thats why weve partnered with JustAnswer, which connects you to certified mechanics around the globe, to get you through even the toughest jobs.

So if you have a question or are stuck, and talk to a mechanic near you.;

Read Also: How Much Mileage Is Too Much For A Used Car

Try The Plunger Method

You know how powerful a plunger can be with your plumbing problems? It may not surprise you to find that a plunger can do wonders for your autos dings and dents. Heres the deets on how a plunger can make your cars exterior look pristine again.

This method is best used on round dents that are small to medium in size. Use a cup plunger designed for unstopping sinks, bathtubs and showers. They also make suction tools that can be used for this purpose.

Plungers work on suction power, so before starting, drench the car and the plunger with water to get a good seal. Position the plunger over the dent and push and pull until the dent pops out. As soon as you hear or feel the pop, stop plunging.

By Using Hammer And Dolly Method

This method is used for medium to large dents and a dent that does not respond to any other process.

We need a rubber mallet or a body hammer, and curved piece of metal or a dolly used to shape sheet metal to apply this method.

The selection of the hammer and dolly is always based on the size, shape and location of the dent.;

If bigger the dent size, the bigger the hammer and dolly size you need.

This process requires a rubber mallet hammer, not a typical building hammer. Make sure before adopting this method.

Using this method for getting the dings out requires placing the dolly on top of the dent first,

And then carefully using the rubber mallet from the inside against the dolly.;

After that, first start hammering from the deepest point of the dent, or the centre, and then gradually work your way through the dent.;

This hammering method only works when the dent can be easily accessed from the rear side of the panel and to reshape the cars exterior slowly.

To successfully use a mallet and a dolly method to get the rid dent out of your car,;

Make sure to first wrap the head of the hammer in a towel to minimize the impact.;

Before hammering, tap the dent lightly with the hammer and keep carefully tapping until the dings pop themselves out.

Also Check: How To Clean Tree Sap Off Car

Simple Ways To Remove Smaller Dents From Your Car

Theres nothing more annoying than getting a dent on your newly purchased car. Even if youre a careful driver, you cant always avoid falling pine cones, wrongly parked cars or pebbles that hit your car when youre on the road. Since getting a dent removed by a professional can be unbelievably expensive, many of us would never consider fixing them.

However, dents, especially small ones, are not worth losing sleep over. There are plenty of ways to remove them from your car by using common household items such as a plunger, vacuum cleaner or aluminum foil. Not all of the methods will work for you, so you should decide which one would be the best for your car.

NOTE: If adentis too large, deep or has resulted in damaged metal, there is, unfortunately, no other way than bringing your car in for a repair.

How To Get A Dent Out Of A Car Hood

A dented car hood can be unsightly, but its possible to fix your dented hood. You can choose professional repair or DIY, sometimes with paintless dent repair, a mallet, or a plunger. For a professional job, expect to pay $150 to $500 to get a dent out of a car hood.;

Find out how car hoods get dented, how you can prevent damage, and what it takes to fix them.

Also Check: Protect Car From Hail Storm

Use Boiling Water On Bumper Dents

If youve suddenly got yourself a dent on your bumper, theres a ridiculously easy fix that wont cost you a thing. All youll need is some boiling water, which youll pour over the area with the dent. After youve done that, explains the writers of Carlock, all that remains is to reach in behind the bumper and push the dent out with your fingers. In the event that the area in question cant be reached, you may actually have to remove the bumper and reattach it once the problem is fixed. Once the dent has been pushed out, pour cold water over the plastic in order to cool it.

Tip : How To Fix A Dent In Your Car With A Vacuum Cleaner

Depending on the strength of your hoover, the suction from your vacuum can help you get rid of a dent in your car.

To help improve the suction levels of the device, you can employ the help of a bucket – simply make a hole in the bottom of the bucket and tape it to the vacuum nozzle.

Place the contraption over the dent and switch on the cleaning device.

If the dent is shallow enough, it should come out relatively easily.

Also Check: Changing Car Interior

Use A Diy Dent Removal Kit

You can order a dent removal kit online or buy one at a local parts store. It comes with all the things needed to remove the dent and the instructions. Follow the instructions and do not try to improvise.;

One thing to be noted is that you must buy the dent removal kit that is meant for the type of dent your car has.;

Hair Dryer And Compressed Air Expansion And Contraction Method

This method uses an infusion of hot air and cold air. As these two come together, they allow a dent to pop out on its own. The hair dryer makes the plastic expand in the dent and the compressed air is cold and makes the plastic contract, essentially popping the dent out. Heat the dented area of your vehicle with a hair dryer at the highest setting possible. Get it as hot as possible and then use a can of compressed air to blow on the dent. The cold air will contract the plastic and allow the dent to pop out on its own.

Also Check: How To Transfer Car Title In Az