Toyota Key Fob Battery Replacement: Step By Step
The helpful team members in our parts department will be happy to swap out your key fob battery for you. However, if you, like a lot of our customers, would like to change it yourself, follow these steps for proper Toyota key fob battery replacement:
More Details On The Ways Of Getting Your Toyota Car Key Replaced
1. Open the key fob. In opening the key fob, you need to press the button on the key fobs side to be able to remove the ignition key inside.2. Pry the fob into halves. In the tiny flat device, you have to find the fob where the metal key ignition is located.3. Detach the green circuit board. In this step, you need to detach or remove the green circuit board to have access to the battery that needs replacement.4. Change the battery. Once you have removed the green circuit board, you will see the round flat battery at the back. Remove this battery and replace it with a new one.5. Replace the battery. After removing the battery, you are now ready to place the new battery in the same slot as before.6. Return the assembly. You are now ready to reassemble the parts, put it back again to how you have disassembled them. Once done, you can test the key fob if it is working correctly. It should function well without any issue.In case, the key fob doesnt work correctly, then, the battery is not the issue. Your key fob must have something more severe than battery problems.
Toyota has many different car models. Each model has its specifications and procedures on changing car key batteries.
Find out which model are you using and if it follows the correct car key battery changing procedures!
What Is A Smart Key
A smart key is an advanced version of an automobile key, one that allows for keyless entry into your vehicle. The car’s onboard computer can detect when the key is near the vehicle and will allow entry into the vehicle without you having to unlock the doors manually.
The car also detects the key while you are inside the automobile and models like the Toyota Prius are equipped with a push-button starting system. As long as the key is in the vehicle, you can just push a button to start the engine of your Prius. It doesn’t need to be inserted into the ignition: It can be in your purse, your pocket, in the cupholder, or anywhere within range of the onboard computer.
Another benefit is that your car won’t let you lock a smart key in the vehicle. It knows the key is there and will prevent the doors from locking. Plus, the smart system automatically locks the doors once you get far enough away from the vehicle.
Smart Keys, AKA Keyless Entry Systems or Key Fobs, Allow Keyless Entry
Manual Key Inside the Fob
You May Like: How To Remove Hail Dents From Car
How To Change Car Key Battery Of Toyota
Anyone can do the programming of the Toyota key fob easily. You need first to insert the new key that you intend to program into the ignition.
Next, turn the ignition ON. After around 8-13 seconds, you will notice that the security light will go on. It will be on for around 3 seconds.
The security light is an indication of the programming of the new key. If the security light doesnt go on, then the key has not been programmed.
It is now time to look at the step-by-step guide of how to change the battery of the Toyota key fob.
How To Replace The Battery In Your Cars Key Fob
If your car key fobs range has diminished, the buttons arent responding to your touch, or the vehicle is having trouble recognizing its proximity, the key fob battery is probably dead.
Yes, it is possible to replace the battery in your key fob, and its easier than you think. All you need is a small, flat-tipped screwdriver and a new battery.
Read Also: Car Title Transfer Florida
Toyota Corolla Key Battery Replacement Guide
An indication that your Toyota Corolla key battery requires replacing is that your smart key or remote control key will not function properly or that the operational range is reduced. To replace the battery in your Toyota Corolla key fob remote, youll need:
- Flathead screwdriver
- For versions of the Corolla without the smart key, a CR2016 lithium battery
- For versions of the Corolla with the smart key, a CR2032 lithium battery
The flat, round button cell batteries can be purchased from most supermarkets, hardware stores or online. To avoid damaging your key fob, take care to avoid touching any electrical components inside the key, particularly with a metal object.
How To Replace The Battery In Your Toyota Key Fob
Is your Toyota Smart Key® key fob not working? It may be time for a new battery in your Toyota RAV4 key fob. When the battery life in your Toyota key fob is low the standard battery life is 1 to 2 years you will hear an alarm in the cabin when the engine stops. Learn how to replace the battery in your Toyota key fob with these step-by-step instructions and a how-to video all you need is a small flathead screwdriver and a replacement battery. Find a Toyota car, truck or crossover to fit your lifestyle today when you visit the Downeast Toyota inventory!
Read Also: How To Remove Scuff Marks From Car Door Panels
Rely On Oak Lawn Toyota For Quality Service And Oem Parts
Still unsure about how to replace the battery in a Toyota key fob or how to program your Toyota key fob? Dont hesitate to contact the Oak Lawn Toyota parts center, where our technicians are happy to help. You can also learn how to reset the maintenance light on a Toyota Camry or how to properly sanitize your car. You can also check our service specials for Orland Park and Countryside drivers.
Which Battery Do I Need
CR2032 is the battery size of most Prius smart keys, but be sure to check your fob before ordering. It could take a CR2016 or another size depending on the vehicle’s production date. Grab a multi-pack and store them in your glove compartment to stay ahead of the game.
At the dealership, we use magnetic precision screwdrivers, which I highly recommend because the internal screws are tiny and easily lost.
How Long Should a Smart Key Battery Last?
A New One Should Last 2 to 3 Years
Don’t Miss: How To Get Internet In Your Car
How Do I Change The Battery Of My Toyota Smart Key
To access the inside of your Toyota smart key fob, release the manual key from its hiding spot and use the opening created to apply gentle pressure to each side of the key fob until it snaps open. A small battery will be housed under the green microchip and should be easy to pop out and replace.
Car shoppers near Birmingham, Alabama can find new Toyota models available with keyless ignition and entry at the Serra Toyota dealership. Stop by or give us a call and let us know what you are looking for in a new vehicle today.
Toyota Key Fob Replacement: If Its Lost
Lets say youve lost your Toyota key fob. That might be a pain, but if you come to Santa Cruz Toyota and order a Toyota key fob replacement, youll be driving around Aptos again in no time. You can trust in Santa Cruz Toyota to always have genuine OEM parts to ensure that youre getting a safe and functional component for your Toyota.
Don’t Miss: How To Know If Car Battery Needs To Be Replaced
How To Program A Toyota Key Fob
How To Change Toyota Key Fob Battery
How to Change Toyota Key Fob Battery: This used car is a 2012 Toyota Venza but same Key Fob Battery or Remote Key design is shared by most Toyota models. You will find it on Toyota Camry, Corolla, Venza, Matrix and others.
Change Toyota Key Fob Battery: Picture below shows a Toyota Venza Key Fob.
A small screwdriver is needed to replace battery on this key fob. Remote key is split in two separate halves and has a slot on one side . Insert screwdriver there and pry key fob open.
Remove inner part of key fob by inserting screwdriver on side slot and lifting it up.
Inner shell will need to be split open next. Release 5 tabs holding inner shell together. Push them inside but careful as those tabs are fragile therefore will break easily.
Lift cover and battery will be revealed. Again, be careful with those tabs. If you break them then a bit of superglue will help.
Slide old battery out and install new battery. Below is the Toyota Key Fob Battery model. Its a 3V CR2025 and is available for purchase almost everywhere, nothing special.
Close inner cover of key fob and place it back on outer shell. Clip outer shell halves together and you just changed key fob battery on your used car.
If you have any remarks and suggestions related to this post or Used Car Toronto in general, dont hesitate to use comment section below.
You may also like…
You May Like: Check Water In Car
What To Do If Your Toyota Key Fob Is Broken
Still not working? If the key is damaged, you can get a new one cut at our Toyota of Brookhaven service center. If the key fob itself is broken, you can replace the case at our parts center. In the event of severe physical damage or water damage, you can get the entire Toyota key fob replaced.
If youve lost your Toyota key fob on your travels around McComb and Vicksburg, youll need to have a new key cut and a fob programmed to match your vehicle. Contact our service team for assistance in providing a replacement.
How To Change The Remote Key Battery For A Toyota
Nearly all new Toyota vehicles come with a keyless entry remote. This small remote attaches to your key chain and can be used to unlock and lock your car, in addition to activating the panic alarm. Some keyless models even allow you to pop your trunk with the push of a button. However, the remote runs on a battery, which will eventually run out of power and need to be changed.
Step 1
Look at the front of your keyless Toyota remote you will see a small indentation in the plastic. This small hole allows you to open the remote.
Step 2
Insert a key into the indentation and pull upward. The remote is going to separate into two different pieces.
Step 3
Remove the thin, circular battery by pulling it up. You may need to use your key to pry it out.
Step 4
Insert the replacement 3-volt battery. On the inside of where the battery is inserted you can see a symbol for either a positive or negative side . Place the negative side of the battery down onto the negative side of the remote .
Snap the two parts of the Toyota keyless remote back together and you are set to resume using it.
References
Also Check: How To Protect Car From Hail
How To Unlock And Start Your Toyota With A Dead Smart Key
Toyota Smart Key fobs house a mechanical key to help you get inside of your vehicle when the Smart Key stops working. Look towards the bottom of your key fob for a small button that will release the inner key, which you can pull out and use on your vehicle like a traditional key.
Once inside, hold your vehicles Smart Key against dashboard while pressing the brake pedal and your push-button should show a green light and allow you to start your vehicle. If this doesnt get your vehicle started and your power door locks also arent working then you might be dealing with a weak engine battery, not a dead Smart Key.
Be Careful Buying Replacements Online
Be very careful when trying to save money by buying the key fob online. While it may seem like a good idea to save yourself some extra cash by bringing your own replacement fob to get programmed, it often ends up being a wasted expense.
Why? The majority of customers who bring in their own that they purchased online were sold the wrong product. It is a high-tech piece of equipment: You can’t just buy one online and expect it to work. Even if you provide the correct year, make, and model, odds are the one you receive will not be programmable for your vehicle.
If you do plan on buying a replacement online, here is one way to help ascertain if it will work: Before you lose your fob, be sure to make a note of its information. There will be a sticker on either its inside or outside. It may be visible after removing the sliding back, the sticker may be on the outside, or the information might be etched into the plastic material itself. Let me repeat: Take note of this information now before you lose your keys and can’t access it.
What you are looking for is the following three numbers:
MDL #: Model Number, FCC: Federal Communication Commission Number, and IC: Manufacturer’s Universal Code.
When comparing prices to the dealer’s prices, always remember to figure in the cost of shipping. I’m amazed at how many customers forget to calculate the shipping charge in their final price comparison.
Write Down These Important Numbers Before You Lose Your Keys:
MDL #
FCC #
IC #
Recommended Reading: Get My Title Florida
How To Program Your Toyota Vehicle Remote
Get in your car, make sure all doors are closed, and have your ignition key ready. Then, follow these steps for how to how to program your Toyota key fob:
The door locks should cycle within three seconds to indicate the vehicle has entered remote programming mode. If this doesnt happen, repeat steps one through three, or schedule service to get in-person help. Your remote should now be programmed to recognize your vehicle! Test it by locking and unlocking the power door locks. To exit remote-programming mode, open the driver door.
How To Change The Battery In A Toyota Key Fob In 2021
Wondering How to change the battery in a Toyota Key Fob? Using a key fob to unlock the car allows you to get into the car super quick.
However, there may come times when the system may not respond. There is no need to panic!
Most likely, your key fob battery needs to be replaced. A professional is not needed for this, and you can get the job done by yourself.
Our extensive guide will tell, how to change the battery in a Toyota key fob!
You May Like: How To Protect Car From Hail
Toyota Key Fob Battery Replacement Instructions
- On newer models, open your key fob using a hidden key that pulls out and inserts into the slot on newer models on older models use a thin object to pry open the cases noticeable notch.
- Expose the battery by gently lifting up the circuit board.
- Check the battery type. Most Toyotas use a CR2032 battery thats easy to find online or in stores.
- Remove the old battery and slip in the new one, then seal up the case.
Once youve changed the battery, test the replacement is working by locking and unlocking the vehicle and starting it up. If there are any problems, you might need to readjust the battery to ensure connections are clean and contact is being made.
How To Change A Prius Smart Key Battery
Considering that a replacement smart key for a Prius can cost anywhere up to, and over $100, were going to show you a step-by-step guide on how to change the battery in one. If you have problems with yours, then this might be a good place to start. It’s not guaranteed to fix your problems, but considering a new battery is much cheaper than a new key, its worth trying before investing in a new one.
What Youll Need
Before you start taking things apart, there are a few things youll need. Firstly, the replacement battery. This is a 2032 button cell battery. Invest in a good brand, they do tend to last longer. And even though it isnt too tricky to change, the less often you have to do this the better. A four-pack of these from Amazon will set you back just over $7.
Secondly, youll need a micro Phillips screwdriver. If you dont have one, I recommend this kit from Amazon. Its similar to a kit I bought for repairing iPhones and it has everything you need. The screwdrivers are magnetic, so the screws will attach to them. It makes the job a lot easier and the whole kit is less than $7.
Not really necessary, but incredibly useful is a magnetic tray. Use this for keeping the screws in. Again, you can get one from Amazon for around $7. You can use anything to keep the screws together, but I have in the past knocked dishes over and thrown screws everywhere, never to be seen again. Just a handy pointer.
Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
Step 6.
Step 7.
Recommended Reading: How To Get Rid Of Spiders In Car
